jeudi 30 avril 2015

0

Outback auto steer help.

I have just moved our outback system from one tractor to another. I moved absolutely everything but steering valve. The mapping works, but when I engage it to follow a line it actually steers away from line! Is it that steering valve? This is a new tractor to us 2009 case 485. It is a s3 outback with sts. I did not install the steering wheel sensor? When I pulled it out of old tractor it had actually broke off and was not doing anything anyways. I think it's the valve or plumbing, thoughts?
Outback auto steer help.
0

High tanin faba beans in south Alberta

Thinking of seeding a few acres of faba. Beans last minute here, heard the expected yield can be from 70-90 bushels an acre. Anyone know if that's realistic or have any experience growing them?
High tanin faba beans in south Alberta
0

versatile 976 hyd. charge press.

Versatile 976 on JD 1900 air cart single fan all hyd. working nornal except HYD. CHARGE PRESS. LIGHT coming on just slightly w. fan running . Light goes out when lifting drill out of ground. Any ideas ?
versatile 976 hyd. charge press.
0

Case 8010 vs Jd 9770 fuel consuption

I have a case 8010 with a 40 ft Dreaper. And a have a frien with a JD 9770 with 35 ft header. He says that his Jd is runnig faster and more economic that my case. Some pictures say it.
I need to renoval my combine this year, and need an advise about this.
Case 8010 vs Jd 9770 fuel consuption
0

jd 7210r v mx200 v puma 210

Hi,

So we are looking for a new boomspray tractor and there isn't much around secondhand so we are looking new. I just want peoples thoughts on the jd 7210r v mx200 v puma 210. I personally think the puma is to small in general size for what we want.

we would be going with powershift also and our boom is 80f 3800 litres but in the future I would like to go 100f 5000 litres. Budget means a 8245 is more than likely out of reach, otherwise I would have gone straight for that.

cheers
jd 7210r v mx200 v puma 210
0

gps signal gone silly !?

ok so today started spraying in a 80 ha field all going well section control , auto steer all good , able to drink morning coffee & enjoy the radio & a look around (trimble 750 with field iq & rtx subscription ) anyway 20 ha section behind a big mob of granite rock & trees sent my gps all silly ,sideways & know where near accurate ! after bout 2 hours of frustration & 4 phone calls , reeboot the system & work out the granite rocks were bouncing the gps signal , dealer had never heard of this problem , has anyone else had this problem ?:14:
gps signal gone silly !?
0

Was this combine a good deal?

Was this combine a good deal?

mercredi 29 avril 2015

0

Price of sweet corn seed

I was told last year that I had purchased sweet corn indeed up being field corn.....looked great tasted horrible... So I found different dealer said he finally got seed in from Monsanto he told the price had gone way up ...no surprise Then he told me it was 85 per pound....totally new to corn said ok to,d him I would pickup tomorrow . After I got off phone I did math that is like 5100 per bushel.....no way I must of heard wrong called up again said no mistake on price that is what it is...salesman said he was supris d on how high it was also....I am guessing they are jacked on their price to me as long as you are buying buy bag I would assume $8 .50 would be a lot closer than $85...this was a dealer in billings mt
Price of sweet corn seed
0

Seed hawk800 rates jumping all over??

Seeding peas with out new seed hawk set the meter at 180 lbs with bean roller in it. They fluctuate from 160-210. just trying figure whats going on mech figured put new motor on but tank 1and 2 doing same thing. It loup3 hydraulic drive.
Seed hawk800 rates jumping all over??
0

TX66 New Holland 94C Draper Header Won't Lift

Hi I just bought New Holland 94C Straight cut Header basically honeybee SP30.
Better rate down point The combine is unable to lift the header it only goes down and the lateral tilt works.
the Header weight is 6283LBS.
Do you think this is the problem or is there a way to increase the hydraulic power? I only have two cylinders on the combine I know there was an I only have two cylinders on the combine I know there was an option three cylinders.
Do I need to add the third cylinder and if so does it just attach with longer pins?
Please help
Thanks
TX66 New Holland 94C Draper Header Won't Lift
0

39' and 44' landoll VT owners question

I'm considering the 39' or the 44' landoll VT plus. I've got a chipped STX 450 and A chipped STX 535 Quad. I would imagine either of these tractors will pull either of these machines in our sandy loam soils but I'd consider pulling an unverferth basket as well. Would the 450 be enough hp then for the 44' and since it measures 44' 9" will a 45' basket work or would I need 46 maybe 47'? Putting a basket behind a disc I always bought 3 feet wider than the disc, same rule for these machines?
39' and 44' landoll VT owners question
0

2012 800 Seed Hawk hyd. drive motor

The other day we started up the feed rolls and 2 of 3 hydraulic drive assemblies cracked on the outer cover. RME tracked down a repair kit which includes new dowels, seals, gaskets, screws and the outer cover. All seemed well until reassembly and we broke the new cover because the bushings are at a shallower depth than the original. The shaft the center gear rides on pushed up on the center of the cover and snapped the housing.
Has anyone come across this before. I got the old "well, we've never had that happen before" story from seed hawk.
Thanks
2012 800 Seed Hawk hyd. drive motor
0

Granular vs. foliar Cu on wheat?

I've got some rented ground going into CPS wheat that I will not be renting next year. I was contemplating going with foliar copper as the granular is over $14/lb actual and I have another friend seeding it and due to drill setup and pre blended fert using granular isn't an option.

Never done foliar copper before. One retailer is recommending going in at fungicide time. I realize it won't build the soil but I'm just thinking about this year.

Any thoughts?

Thanks.
Granular vs. foliar Cu on wheat?
0

WTB: 40-60hp older loader tractor

Hi there,


I am looking for a cheap older loader that still runs/drives in Ontario, Canada for use at a cottage.


If anyone has anything worth mentioning for around the $3500 range feel free to PM me.
WTB: 40-60hp older loader tractor
0

Grain box manufacturer

I am getting prices on having a grain box built for a tri drive truck. I
am finding companies in Manitoba that build boxes much less expensive than my local box manufacturer here in Alberta. There is a hutterite colony that builds boxes in Manitoba .... anyone know what their name is? Do they manufacture a good product?
Grain box manufacturer
0

2320 help

Having problems with the front box not metering. one half comes out super quick blocking the lines and the other half has nothing. Were only putting 70kg ballistic down. The rear has oats flowing very nicely. when not blocked the fan speed on the monitor is 3600 and the rear is 3400. any help or ideas would be awesome cheers elmirafarms
2320 help
0

Back To The Basics Supplementation

The moon's put together I'll working for women but also from into routines for 90 days step-by-step muscle building workout you know muscle bills fat ladies and I don't be afraid to have to battle must you not going to get bring in huge in a and blocking I then at the end we've got one hundred the best strength training workout plus 25 kick butt workout school from Tom kilos Maximum Shred imagine having 125 workout so you even if you don't want any the other things that showed you having these workouts training workers so you can quickly access and take the gym or be my home care perfect next up we have our body weight and sports business resources so these are actually really cool I love these ones on because a little bit different but on their challenging inhere they're amazing so Navy SEAL workout.

http://ift.tt/1HQde8F
Back To The Basics Supplementation

mardi 28 avril 2015

0

1910 calibration question

New to john Deere carts came from bourgault and I was trying to calibrate my cart for the first time today and it says to first set your transmissions to 50 and than I turn on my hydraulic crank and it cranks out around a 100 revolutions and I weighed it and it gave me a number to set my transmission at but it was a fair ways away from fifty it was 24 so I set it to 24 and went to recalibrate it Again cause on my bourgault cart usually the first time you calibrate it gets you close usually within 5 percent but than if you calibrate it again it gets you to within 1 percent but on the Deere when you go to calibrate with your new transmission setting it asks you again to put the transmission at 50 again before you calibrate? Isn't that defeating the purpose cause it's gonna give you the exact same result again than. Or do you just ignore that message and calibrate it with your new transmission setting?
1910 calibration question
0

Help 1910 tank pressures

I started seeding yesterday and I'm wondering if anyone has ever had the issue I'm having. the front take has phosphate in it and when the fan isn't on all the tank pressure gauges read in the green when i close the lids and turn the fans on all the tank pressures read in the green again but when i turn the meters on for some reason the front tank pressure gauge goes to left about an inch out of the green toward the lid open side. any ideas by chance? when parked with the fans on i have raised the lid a bit without the meters turning and there is definitely pressure in the tank. I have the 430 bu double shoot cart and iv blown out the tank gauge lines and the lines feeding pressure to the tanks and iv blown out that little passage way where the pressure lines connect onto the meter area. I'm still getting product coming out just not sure if its at the right rate or even? any ideas would be appreciated. maybe its jus not a big deal and i should just giver.
Help 1910 tank pressures
0

Buying tools and supplies online

Does anyone know of any good websites to buy misc stuff like possibly stainless steel chain or re-capped semi-tires.

Generally ebay and amazon don't have a lot of these kinds of supplies
Buying tools and supplies online
0

Best small engine dealer???

So where are you guys buying your auger engines? Anyone with good prices out there? Not particular on brand really, for the use the auger gets...

Just need a 20-24 horse for my 8 inch by 46 Sak.

Thanks
Best small engine dealer???
0

Air Drill drift

Air drill is tracking down on very minor sloped side hills, we didn't have this problem last year.


Tractor TCM is properly adjusted.


Do I need the attachment to steer the Air Drill ?


Thanks,


MS
Air Drill drift
0

Fendt 939 SCR vs T8.420 Autocommand with ripper and plough.

0

John Deere 9510R Axle lube error keeps coming on

Anybody have axle lube error come on? I had it come on they replaced sensor, came on again.
John Deere 9510R Axle lube error keeps coming on
0

Flexicoil 3450

Hi. Looking for some help on our air cart. It's a variable rate 3450. Has been working really well last few years but has started acting up as of late. Was seeding peas the other day out of the rear tank and near the end of the day the meter roller started acting up. Monitor would say tank 3 is shorted or open and rate would go to zero. Id turn out and wait a bit then it'd work fine for a bit then the same problem would happen. It's pretty frusturating to say the least. Managed to finish the field and pulled roller out all bearings seemed fine as I thought maybe that could be the problem. It seems maybe it's an electrical problem but not to sure. We changed the shaft speed sensor this morning but haven't tried it out yet. I thought maybe it was the tank 3 switch on the tank but I switched tank 3 to run off tank 1 switch and it still acted up the other day. No great service support on these tanks it seems the service guys don't know much about them. Any one ever run into this issue? Any help would be greatly appreciated. Thanks
Flexicoil 3450

lundi 27 avril 2015

0

rem 2100 grain vac problem

Hello, I have a rem 2100 grain vac and I am having a problem getting the top section of the auger to lock out. It pushes out about 1" short of locking with a tight seal. It also does not stay tucked in when putting it down, it flops out, but will go back with little effort by hand. I have pressure checked the cylinder the section is on and it has to sign of leaking seals. What next?


PS. the bottom cylinder works fine.
rem 2100 grain vac problem
0

Case 3430 air cart monitor problems

Having trouble with the monitor. When I turn the power on to the monitor the message "no remotes installed" is displayed or "communication error". If I shut the power off to the monitor 2 or 3 times then it works for a few hours but goes back to displaying one of the above messages. Any ideas as to what's causing this or how to fix it?
Case 3430 air cart monitor problems
0

Broken reel shaft- 3152

Hi , I am running a new 3152 45ft case front. The centre shaft of the reel on the LHS when sitting in cab has now broken 3 times in 500 hours of use. It breaks right at the end of the reel where a flange has been welded onto it, suggesting to me it may of been to hot when welded...have any other users of this front experienced this problem? Other than that I can't fault the front at all, just hope a pip is not far away.
Broken reel shaft- 3152
0

6.50 x 40 Inch tyres , Aus

,
Having just aquired a 16 Run Massey 500 series combine (seeder) on the weekend I am in search of a pair of 6.50 x 40 tyres, I think they were a type of multi rib originally.

I know they will be as rare as rocking horse ****

Have googled and 40 inch doesn't even get any hits.

Would anyone know the where abouts of a pair pls. WA pref.


Thanks

Arro
6.50 x 40 Inch tyres , Aus
0

Tr 99

I just bought a 99 2wd. I want to add a chaff spreader to this unit. What is a good brand and is there a spot on the hydraulic bank to hook it up. TIA:trac1:
Tr 99
0

Cih MX110 good bad? - value???

Whats a '98 MX110, loader, joystick,16 speed, not quite 4000hrs on it worth. These were decent tactors build in the USA weren't they?
Cih MX110 good bad? - value???
0

Alliance Tires / BKT Tires

Looking at Tires for my MFWD Genesis
80% Haying / Cattle
20% Light Tillage


Are these brands worth the cost savings ?


Thanks
Alliance Tires / BKT Tires
0

Double NH3 trailers??

What size tires and setup do most guys use on their double 1500 or 2000 gallon NH3 trailers? I have P and H double 15 trailer with single tires on the back I think they are 16L something something size. Well I seem to need more tire as the back always wants to sink. Wondering if I should look at getting a trailer with tandem rear tires or if just going wider tires like a 21L would work. If you have pics of your setup please post. I will look at my tire size for sure tonight and try and post a pic also. thanks
Double NH3 trailers??
0

Header 2388

I need some help with my header
Why would I have differing resistance on the ignition key between when I turn it on & when I turn it off
Header 2388
0

international 615 combine height

I was wondering if i could haul a 615 on my gooseneck trailer i know it will haul it just wondering if it will clear wires or bridges
international 615 combine height
0

GreeNeem Coir

Neem Coir - 100% Natural Eco Friendly Organic Multi Purpose Growing medium/Potting medium made from renewable Coir and Harnessed with the Neem power to exhibit Pest repellent and Nematicides property.

GreeNeem Coir is a Careful Blend of a very Special Grade of CoCo Coir and GreeNeem Cakes.

Coir is fiber, processed from the coconut husk. It is a fine, flaky bye-product. It is a high quality vegetable fiber.

For More information kindly visit us at Greeneem: Neem coir,coconut husk chip,cultivation pots ,nematicide
GreeNeem Coir
0

CoCo peat / Coir Peat Organic Multi Purpose Plant Grow Medium

Largest Producers and Exporters of 100% Natural organic Multipurpose CoCo Coir Peat Plant Growing/Potting Medium of different grades for different grower needs and applications.

For More information kindly visit us at CoCo Coir Peat: Coco coir peat-organic multi purpose plant growing medium/potting medium, best water saver
CoCo peat / Coir Peat Organic Multi Purpose Plant Grow Medium

dimanche 26 avril 2015

0

help with 2594 power shift

Hi there,
So I have a 2594 with the 24spd. It was working fine, shifting smoth through all 6 power shifts. Recently I started it up and it only shifts from 2-3 and 4-5. So I only have 2 power shift ranges at the moment. Anyone have any ideas? I checked the shift solenoid wires/connections with no luck. It doesn't even try shifting into the other ranges, so I think it must be electrical.

Thanks.
help with 2594 power shift
0

WTB digital dash for 976 versatile/ford

Ours has broke and dealer doesn't service them anymore.
WTB digital dash for 976 versatile/ford
0

Tell me about a 9470R !

Looking at upgrading tractors. Got a 9470R coming for a demo. I really wanted to see it on my drill but too much setup for a day, it will be on deep tiller doing anhydrous I guess. Just wondering if there's anything to look for, I've never had a green tractor on the farm before! What are owners thoughts, good and bad. I also wondered what you guys are running for hyd pumps. 58gal cuts it close on dual fan drill but it's $15,000 to go to big pump!
Tell me about a 9470R !
0

Case ih air drill w 2300 cart into variable rate drive?

We have a ground driven case ih 4006 double disc air drill with a 2300 two compartment cart. It has the slide on the bottom of the tanks that you manually open and close to adjust your seeding rates. I have hear of the Rawson drive system but is their any way of making that slide itself electric/hyd operated? On our case monitor there is a switch to adjust + or - I was looking to see if there was an add on from case to utilize that but I couldn't find anything.
We have a loup population monitor in the cab so the ability to adjust that slide from the tractor would be really nice. Thanks!
Case ih air drill w 2300 cart into variable rate drive?
0

combine badging

Simple question not very familiar with new hollands badging thought case ih was getting confusing. So is a 9080 the same machine as an 8090 just a series older? Just surfing the net for some used machines and finding the model badging a tad confusing.(I have allways run caseih) thankyou.
combine badging
0

R65 on Tractorhouse

Real nice 2005 R65 on tractorhouse for $55,000.Sitting in my shed,wired for a Macdon.
R65 on Tractorhouse
0

L3 Shoppers Heads Up

Auction May 2nd at Zap N.D.has 2 L3's even the sought after green stripe with 24 rigid head.Wolf Auctioneers has the sale.
L3 Shoppers Heads Up
0

Con job- Ace Industrial Supply

Has any one else had to deal with them?
They called me up and offered to send me a set of drill bits to try out, for free. I received them. A small drill bits set ( very small 29 bits), never tried them. after a couple of months I received a BILL for $378.39. U.S dollars I'm guessing.

They have continued to send me bills, and now are calling and threatening legal action.
What interesting is they have never ask for their product back.
I am not paying them!

If they want to send me a check, for shipping and HANDLEING, I will send the drill bites back.
Con job- Ace Industrial Supply
0

BG 7700 fan question

Hoping someone has a fix, have a Case quad with twin 55 gpm pumps hooked to a new BG 7700. Have changed couplers to 3/4s, problem I'm having is I can't seem to get more than about 4800rpm out of the fan or fans at 100%! Dealer is looking into it, we are pretty confident it's not with the tractor. Maybe I'm missing something! Thanks
BG 7700 fan question
0

Jd 1910. Metering cartridge

Having problems getting the meter to lock in place It locks good on the rear tank and other meters work in the rear also but none in the front tank. It's all clean and looks ok but no luck. Any ideas very welcome. Thanks
Jd 1910. Metering cartridge
0

seedstar 1 1910 cart

Have a neighbor that when turns on tank 1 on brown box tank 3 turns on and vice versa.
seedstar 1 1910 cart
0

Flexicoil conveyor

Does anyone know if you can get a conveyor on the new 430 bushel flexcoil air cart? Or is a new series coming or something the case website doesn't give much info.
Flexicoil conveyor
0

Renovating older alfalfa stand

Has anyone scratched there harrows over there alfalfa in early spring ?
To air it out and get it going ?
Renovating older alfalfa stand
0

Rantoul, IL 2005

,
0

Will County Threshermen's Association

Will County Threshermen's Association

samedi 25 avril 2015

0

5&4 Auxillary stuck in gear

I have a Chevy c70 with a 5&4 and a 427. When we bought the truck at a auction it worked well... a few weeks later the aux tranny was stuck in drive. I took the top plate off the trans and there was some metal fragments in it but you cant tell where it came from....What would have broke away in there? I took a video of it....

5&4 Auxillary stuck in gear
0

1910 pressurization issues

Hi, new timer to this site. Have a question on 1910, 430 bushel jd cart. Problem is pressure gauge for front 150 bushel tank is not going into the green (all is normal) mode, but stays in yellow. We have rebuilt this particular meter housing and did find blockages in ladder rungs (that pressurize tank) and in the air channels in the meter housing itself. All was well before we started seeding, and we are not finding any significant air leaks.

Thanks in advance for any help.
1910 pressurization issues
0

Liquid 28% on HRSW?

Most of the wheat is on fall fertilized ground and the rest spring fert. All was variable rate applied. My question is how much 28% should I apply and at what time for both yield and quality? We have the stream nozzles as we have tried this before. Just looking for some tip and expierence. Thanks!
Liquid 28% on HRSW?
0

3310 raise/lower issue

I have a new to me 3310, I can't seem to get the toggle switch in cab to raise/lower openers properly. What I end up needing to do is turn switch to raise with remote in forward position, then I need to take remote to "neutral" position then push it back forward, then it raises the openers. Same goes for lowering.

Am I missing something obvious here?
3310 raise/lower issue
0

Borgault 5710 and 6450.

2004 5710 hoe drill. 40ft. MRB DS. 9.8 spacing. 3/4 BTT KO carbide openers. Rubber packers. 591 monitor. 23,000 acres.
2008 6450 TBH tank. 4 tank metering. Hydraulic auger assist. Bag lift. 14,400 acres.

Shredded. $95,000 OBO. Will split.

Be hard to find one in this nice of shape. Planned to use this season and only reason I'm selling is took on more land so a bigger tractor and drill were required and dealer wouldn't deal for trade.

Drumheller AB. 403-334-0955. Can send pics.
Borgault 5710 and 6450.
0

2010 MF 9635 Price

I am looking at a 2010 9635 with 1,100 engine hours and 750 header hours, in great shape, with new turtles, looks to have been taken care of.

It is listed for $78k, what would you say would be a fair cash offer? I was hoping to be around 70.

Thanks
2010 MF 9635 Price
0

Flagship combine rotor gearbox output shaft seal failure.

All flagship machines in my area are set up for rice. I have had a couple that have lost the rotor gearbox seal and some multiple times. What I find is a birds nest wrap around output shaft and straw in seal. I am trying to make a shield with a pipe around shaft to keep straw away from seal. Im also planning on putting key stock on outside to keep straw frow wrapping aroung outside of shield. Has anyone had this problem and done anything different? Attached is a picture of a shied but but it had a huge straw donut around the outside of shield.

Flagship combine rotor gearbox output shaft seal failure.
0

Is Jim Prentice getting dumber by the day?

This will only interest Alberta members but obviously anyone can post.
Our current Premier Jim Prentice called an election a year early thinking some political maneuvering recently done would allow another cake walk to extend 44 years of Progressive Conservative majority rule.

Not working out too well for Jim.
The leaders debate was Thursday night.
Since Jim sees the NDP as the main competition he focused on leader Rachel Notley.
Jim made the statement that the NDP would raise corporate tax to 20% to which Rachel corrected him that she would raise it BY 20% from 10% to 12%. To which Jim told her math is hard. Must be. Jim was the one that was wrong, if you are going to spout such a condescending remark at least be right.

So the next day Jim is telling voters they do not want an NDP government nor do they want to vote NDP.
Really?
You are telling me how to vote not asking me for my vote?
What an arrogant attitude, the kind of attitude that comes from being in power far to long.

Bye bye Jimmy.

ABC!:)

(Anybody But Conservative).

Over to you AB!
Is Jim Prentice getting dumber by the day?
0

Enjoy Site For 18+ People

The rest of the day to step into the light can sell for Alex seal the deal would date and Robin Tommy funny come face to face Sarah but we'll see like what you see so far x&a pick it up in a dark what will happen when we hit the life having Tommy both for the first-ever without saying her and Tommy fancies his chances of two from serious makes him but it all comes down to this they're like reveal date it's like to feel that I she half can concerns AffairAlert about saying I actually liked I'm a little bit worried about whether his No might be a little bit too much where-he's a little bit to use dialed in grains but he definitely looks after himself and I I like that about him a pic send Jade the life they'll I did that occurs from talking to head-the way she acts I think it can be more physically my type what if the next time ask the person asking.

http://ift.tt/1GtvVAn
Enjoy Site For 18+ People

vendredi 24 avril 2015

0

new idea 5312

I have a New Idea 5312 center pivot that needs a bottom roller. I rebuilt the cutter bar and within 100 acres the bottom roller broke. I am interested in buying another machine for parts, or maybe selling mine for parts. it is a good mower just needs a roller, and agco doesn't make rollers anymore.
new idea 5312
0

ISEKI Parts

ISEKI Parts Catalogues I found here
ISEKI Parts
0

Global Warming ‘Pause’ Extends Nearly 18 And A Half Years

The photo caption used for this article is priceless.



Global Warming ?Pause? Extends Nearly 18 And A Half Years | The Daily Caller
.
Global Warming ‘Pause’ Extends Nearly 18 And A Half Years
0

chemicals to stay away from?

Any chemicals to stay away from handling wise? Salesman pushing lorsban, but I have read some bad things on it.
chemicals to stay away from?
0

looking for truck drive or combine driver for wheat harvest

looking for truck driver or combine driver from may 15 tell nov






Cole Mawhirter-620-377-7099
looking for truck drive or combine driver for wheat harvest
0

Increasing wheat yeild and quality

Would like to know what practices you have implemented to your operation and noticed an increase in yeild and quality. Thank you

In the last couple years:

We have been applying fungicide at 10% flowering has improved our quality significantly.

We top dressed 10gal of 28-0-0 at 3 leaf and boosted our yeild at least 5 bu/acre and protein was in the 14-15 range with a couple loads hitting 16 non topdressed was 13-14.
Increasing wheat yeild and quality
0

KX7 Concaves are Now Available through All States Ag Parts

KX7 has partnered with All States Ag Parts to bring you our complete line of concaves. All States offers an easy-to-navigate online store with a diverse product line. With the addition of KX7, shopping for our concaves is now quick and convenient. Whether you're looking for full MaxThreshTM or MaxRoundTM assemblies, or individual box insert replacements, All States Ag Parts is your source for KX7 ag parts.


Visit their online store today: Combine Parts | All States Ag Parts
KX7 Concaves are Now Available through All States Ag Parts
0

Agco RG700

Has anyone had issues with the tank lid leaking? It appears the lid flange is not properly mounted or is poorly engineered. What a disappointment. It would be like sending a new combine out of the factory with a 360 bu grain tank that has a big hole at the 325 bu level. So you have to mess with it before you can get your true capacity.

And 2 major hydraulic lines just coming loose. Lots of oil sprayed all over the undercarriage. Maybe its part the anticorrosion program. Sound off
Agco RG700
0

Flax seed in Eastern Manitoba or close?

Does anybody have any nice bin run flax for sale? I have bought some certified but need about 2 hundred bushels more and dont want to pay the big price. PM me or email me at mcintp1@mts.net . Thanks
Flax seed in Eastern Manitoba or close?
0

Light clutch prime mover choices

Looking to upgrade from the old Circus Truck (Leyland bx-9) to a prime mover tipper set up - local freight costs are killing me! Some reliability wouldn't hurt either. Only looking to cover 10-20,000km max per year on flat roads doing local hauling.

Got the cart before the horse,already purchased seed/super tipper so now need the prime mover. However truck choice is being dictated by my left knee not my wallet! Footy injuries and wear and tear (read "old age") mean I can't handle non assisted clutches, neither can my worker.

Sick of old crappy gear so looking MY 2000+ spending up to $50k so I can get something reasonable. Drove an Isuzu Giga 425 with 18sp RR today and got on well with it. Looking at FH/FL Volvo's also.

Any other makes I should be looking at?
Light clutch prime mover choices
0

New holland t9030 4wd tractor keeps stopping

Hi all, we have a new holland t9030 (same as an stx) that keeps stopping randomly. Seems to be an electric issue as its as if you turn the key off, the whole thing just shuts down, then starts as normal when you fire it back up. We are currently sowing and it is really annoying, and we are concerned that it is going to do it while we are driving down the road! We have checked all earths, and the auto electro toon has been all over and can't solve it, any ideas would be much appreciated, thanks
Mango
New holland t9030 4wd tractor keeps stopping
0

Looking for truck driver for 2015 silage season

Wanting to find a truck driver to haul silage starting May 2015. Will possibly turn into year-round work after silage, hauling manure & commodities. Based out of SW Kansas. Wage based on experience. Contact Jan Burger. 620-952-2987 or bloubul8282@hotmail.com.
Looking for truck driver for 2015 silage season
0

Can newly emerged flax take some frost?

We are going to be seeding some flax this year and was wondering how early a person can seed it. Can it withstand some frost after it emerges or does the frost kill it dead? Does anyone know how soybeans handle frost as well? Thanks SouthernSK
Can newly emerged flax take some frost?

jeudi 23 avril 2015

0

John Deere 2630 GPS will not work!!

Has anyone else had this problem with a 2630 monitor. When I start tractor and go to use GPS only 1/4 of the pie chart is colored in. The list says everything is good but it wont let me enable the gps. In order to get it to work I have to do a cold reboot (shut off tractor, unplug monitor, start tractor, plug in monitor). Any advice would be appreciated. Thanks
John Deere 2630 GPS will not work!!
0

John Deere 2630 GPS won't work

Has anyone else had this problem with a 2630 monitor. When I start tractor and go to use GPS only 1/4 of the pie chart is colored in. The list says everything is good but it wont let me enable the gps. In order to get it to work I have to do a cold reboot (shut off tractor, unplug monitor, start tractor, plug in monitor). Any advice would be appreciated. Thanks
John Deere 2630 GPS won't work
0

Help versatile 485 hydraulics only 4400rpm fan

Cant get our 2011 485 versatile to run the fans fast enough on our seed hawk 800 tank. It has dual fans but cant even get one to go over 4500. Anyone have a idea what to check
Help versatile 485 hydraulics only 4400rpm fan
0

Bolts for plow

I have the problem of breaking the bolts of that hold the disk blade onto our Allis 4 bottom plow which is 3 point mounted. We have replaced them with new bolts every time. What type of bolt would you recommend as far as strength goes? This problem happens about twice each season and is a big pain but not expensive or hard to fix. Even had the neighbor use it on his tractor and same thing happened. Any suggestions would be great.
Bolts for plow
0

ET was on set with the adorably

ET was on set with the adorably young actors, 22-year-old Mark Wahlberg and 19-year-old Leonardo DiCaprio, as their epic, A-lister friendship began to blossom back in 1994. Their friendship continued over the years. They reunited on the big screen for The Departed in 2006, and still remain friends today, hugging it out whenever they see each other.


http://ift.tt/1HxKrFN
http://ift.tt/1HxKrFP
http://ift.tt/1HxKq4F
http://ift.tt/1HxKq4K
http://ift.tt/1HxKq4M
http://ift.tt/1HxKq4O
http://ift.tt/1HxKrFX
http://ift.tt/1HxKq4S
http://ift.tt/1HxKql6
http://ift.tt/1HxKqla
http://ift.tt/1HxKrWj
http://ift.tt/1HxKqle
http://ift.tt/1HxKrWn
http://ift.tt/1HxKqlg
http://ift.tt/1HxKqlk
http://ift.tt/1HxKrWp
http://ift.tt/1HxKqlm
http://ift.tt/1HxKrWr
http://ift.tt/1HxKqlo
http://ift.tt/1IO5T8a
http://ift.tt/1IO5T8c
http://ift.tt/1IO5R03
http://ift.tt/1IO5T8g
http://ift.tt/1IO5T8i
http://ift.tt/1IO5T8m
http://ift.tt/1IO5R09
http://ift.tt/1IO5T8o
http://ift.tt/1IO5ToE
http://ift.tt/1HxKscR
http://ift.tt/1HxKscV
http://ift.tt/1HxKscX
http://ift.tt/1HxKscZ
http://ift.tt/1HxKsd1
http://ift.tt/1HxKstj
http://ift.tt/1HxKqBU
http://ift.tt/1HxKqS8
http://ift.tt/1HxKqSb
http://ift.tt/1HxKqSe
http://ift.tt/1HxKstq
http://ift.tt/1HxKstt
http://ift.tt/1HxKsJK

http://ift.tt/1HxKsJM
http://ift.tt/1HxKqSm
http://ift.tt/1HxKqSo
http://ift.tt/1HxKsJQ
http://ift.tt/1HxKqSq
http://ift.tt/1HxKsJS
http://ift.tt/1HxKsJU
http://ift.tt/1HxKtNS
http://ift.tt/1HxKtNU
http://ift.tt/1HxKtNW
http://ift.tt/1HxKsJY
http://ift.tt/1HxKtNY

http://ift.tt/1IO5WAX
http://ift.tt/1HxKsK2
http://ift.tt/1IO5WAZ
http://ift.tt/1HxKt0g

http://ift.tt/1HxKtO0
http://ift.tt/1IO5UsQ
ET was on set with the adorably
0

Case IH 8120 combine for sale

Hey Guys, (hoping this isn't against the forum rules)
I have a friend who is selling his 2012 8120 combine due to illness. He is asking 249,900.Canadian Has 1033 hrs and 723 separator hours. 425 hp. Also has a 12 row 30" corn head and a 40' draper head for sale. Its in Ontario Canada but they have experience with equipment going across the border so they could help with that. He is hoping to move it sooner rather than later.

Case IH 8120 combine for sale
0

JD 1700 planter 2630 screen

Going to run a 1700 for the first time this year. It has a 350 computer trac monitor and radar with it?

What would we have to do to have population etc come up on a 2630 display?

I assume it would need some sort of controller? Ta

Will
JD 1700 planter 2630 screen

mercredi 22 avril 2015

0

Cappelo CornHeads

Want to ask how you all are doing with your Cappelo corn heads...good bad or in different..Thanks
Cappelo CornHeads
0

2014 Cappello cornhead

wanting to sell a 2014 quasar 830 folding head...red in color fits flagship...asking $ 92000.00 Thanks for looking
2014 Cappello cornhead
0

First SP Swather Help

Hey all, I'm new, interested in some opinions...
I am looking for a SP swather, model year 09 or newer, 700-1500 hrs, and something I can switch off between a 25-30' draper and a disc head. A few I'm looking at include, 2009 Case WD1903, 2010 NH8060/8080 and a 2010 Macdon M200.

I really would like a rig that I can get going with the disc head and then not have problems finding a reasonably priced draper closer to wheat harvest.

Be great to hear from everyone but specifically those who run both disc and drapers in same season.

Thanks
First SP Swather Help
0

1910 air cart siphoning fert

Have a six run 430 bushel tank and on the 80 bushel tank on the 3rd run fert siphons out of meter when, standing with fan on. Have tried different meters. Anyone with any experience in this issue.
1910 air cart siphoning fert
0

Sydney is enduring another day

0

Case 24sp Transmision Issue 9350

I recently bought a 97 9350 case, 24 speed, 6000 hours. Farmer owned but worked hard. I know nothing on the history of it. Ive got two issues, the second I actually need to fix.

Problem 1 - Shifting into 1 or R is hard. Ive read these transmissions are hard to shift, ive also read maybe change the cables/adjust them. Doesn't matter if tractor is running/moving, or anything its just harder to move the shifter into those gears. Any other advice on this?

Problem 2 - When tractor is started (doesn't matter over night or off
for 5 minutes) I can put both shift levers into gear and it will not move. Seams like the clutch is fully engaged? If I slowly push the shifter into gear the gears in the tranny are slowly turning, i can feel them grind slightly and the shifter will roll into gear. The tractor will still not move (will rock very slightly when clutch rapidly pushed in and out) . After about 15-30 mins the transmission will start working fine, clutch works, all gears work. Operates fine until I shut it off. Any ideas?

To me it seams there is a pump or pressure system that is not getting pressurized, or primed, once it has prime it works fine. Until it is shut off and then whatever system (my guess is clutch) looses prime then needs to wait to build back pressure/prime.

Also reverse/first being on the top of the transmission near the clutch could the two problems be related? Lubrication/trans pressure related?

Any help is appreciated, Thanks in advance.
Case 24sp Transmision Issue 9350
0

Wanted - 1995 IH 8100 owner's manual

I am looking for an owner's manual for a 1995 IH 8100 tandem axle semi.

Let me know if you have a manual or a PDF file of the service manual.

Thanks

c_m_link@hotmail.com
Wanted - 1995 IH 8100 owner's manual
0

John Deere 750A

Dear All, i am a John Deere 750A virgin having an issue with the electric metering system alarm coming on - alarm symbol = metering unit followed by shaft rpm-gears symbol , sensor symbol shaft rpm

description =Metering device speed not matched to selected meter record-Check record settings, meter settings, and calibrate as needed. Check meter sensor.

i have switched the alarm off but cannot figure the root cause. drill seems to be going fine. It was on fine seed setting when it was delivered for this demo. i have switched it back to coarse seeds and it displays as such through isobus screen.

any help welcome, it is recording shaft speed.

Attached Images A63818.gif (4.6 KB) 
John Deere 750A

mardi 21 avril 2015

0

Cameras on Bourgault 6550

Wanting to put a camera in the canola tank on a Bourgault 6550. How do you guys mount it cause you cant see the auger from the top of the tank? We do have the X30 monitor so is the count down close enough that you can just go off of that?
Cameras on Bourgault 6550
0

Need help with John Deere 1900 air cart

Hello, I bought a used 53' 1820 with a 1900 cart that has has the 1910 meter boxes on it. It has 3 tanks and I did the rate check on the rear and third tank with some fertilizer. I set the rear tank to 120 lbs and the 3rd to 50 lbs product rate with the fan set at 4700 rpm. I did a few short passes to check if it works and it plugged 4 of the 5 top fertilizer runs. After I spent 2 hours clearing them I noticed that the top runs have half the airflow of the bottom / seed runs. No matter where I set the air dampener the bottom runs have way more air pressure and the top run just seems too wimpy.

Any ideas ?

I read in the manual that on a tow behind the damper crank should be on the bottom, but this on is on the top, could someone have put it in upside down ?

Should there be any difference in airflow between the top and bottom runs?

I'm new to john Deere and I'm already got not liking this thing. Any help appreciated
Need help with John Deere 1900 air cart
0

bourgault 6450 on flexicoil -newholland tool

have anybody made a hitch for a newholland (flexicoil) airdrill to hook up a bg tank 6450 ?

how did you guys make it?
thanks
bourgault 6450 on flexicoil -newholland tool
0

agleader controlling JD section control

I/m thinking about a sectional control for my 1910 cart, does anyone know if my agleader integra will control it.I controls my sprayer, but not sure how the john deere is controlled thanks
agleader controlling JD section control
0

Grain millers Yorkton to stop buying oats dessicated with glyphosate

And it starts.....

http://ift.tt/1GgE5ck
Grain millers Yorkton to stop buying oats dessicated with glyphosate
0

2013 S680 updates or PIP

Thanks to the forum I got my door seal, auger and shoe fixed at my local dealer under PIP at no cost to me. They ran my ser number and says they don't see any more updates. My question is are there more I need to ask about? They didn't know about these three are there more. Thanks for the help happy planting.
2013 S680 updates or PIP
0

Deere 777 (FC 1110) rate problems

So I was out sowing some grass seed for the father in law last night and was putting down 100kg/ha of map down the tube. I weighed a sample of the map and worked out the density which worked out to be 1.019kg/L or 64lb/cu. ft. The charts and math formula says that I should put the gearbox setting to 22 so I put it on 20 just to be safe. I put 1.43 tonne in and sowed 12.5ha so I should have had about 180kg left in the tank but it ran out. So it's going out about 15-20% heavy.

Drill is 7.2m (23.5ft) wide. Shaft speed sensor seems to be reading and hasn't been erratic. Bins seem to be sealing properly. It's a tow behind with the fert in the front bin (closest to bar/tractor).

Anyone got any ideas on what I should look at checking or looking to replace/swap out?

Cheers

Mark
Deere 777 (FC 1110) rate problems
0

JD 1770 frame control

I have a JD 1770NT CCS 12 row planter. I planted 50 acres with it just fine and folded the planter in, put it in transport mode, and then the planter would not pick up at all. The markers will not work either. All of the hydraulics(pick up, markers, and folding) run into a mechanical control box mounted on the planter frame. Nothing electronic. Anyone have idea as to what is wrong? Thanks.
JD 1770 frame control
0

Montana Winter Wheat

I took a short drive on the Highline yesterday ,north of Harlem it looks nice no sign of winter kill fair growth .Havre through Kremlin and over to Guilford it looks excellent the stubble is almost covered and real nice .From Guilford west to Chester it looks like will struggle if there isn't a good rain soon ,it just looks a bit more immature .
A couple good timely rains look like a good crop on the way ,BUT that is every crop every year I guess .
Montana Winter Wheat
0

Case 4690 Hard steering

Hi. Has anybody had a hard steering problem with a 4690. We have 2 4690's and one steers a lot harder than the other one. Any ideas?
We'll be checking the service manual but thought someone might have had this problem before. Thanks
Case 4690 Hard steering
0

cultiva atc

Have Cultiva ATC not working. Looking for a place to have repairs done. Can anyone help me?
baudinfarm14@gmail.com
cultiva atc
0

Honeybee on a R450

At first when changing to the WS Grain header from the rotary the tilt, reel up/down, reel fore/aft didnt work. After going in and double checking the address change, the only thing that doesnt work is the fore/aft. Any ideas other than a fuse problem.
Honeybee on a R450
0

Who`s planting Australia

Anyone planting yet? No doubt there`s some feed oats gone in and maybe some dual purpose long season wheat, some Faba bean and maybe some early barley going in now.
Who`s planting Australia
0

Cab cam

Hi guys,

I want to run three cameras in my 2320 cart (non plastic walls, pitch black).

I have read countless threads on here about cab cam vs ag cam's. It appears that ag cam's are better from those that have used both.

However, I would like to hear from a farmer who has used cab cam's (the cheaper of the two) how the cameras performed in this dark setting. Would you spend the money on them again?

I would be going with a wired system.

Finally, anyone used an eBay setup and what were your thoughts? They look very similar to the others in the industry.

Thanks for your help and sorry for another camera post, I just couldn't find a straight up answer about cab cam's in dark tanks in my searches.
Cab cam

lundi 20 avril 2015

0

AgLeader Integra in my Sprayer

I just put the Agleader Integra monitor, Ontrac3 steering and their DirectCommand application control in my Sprayflex sprayer. It replaced a light bar and Raven 450. I really like the Integra Monitor. It's simple, easy to navigate, and was easy to setup. The Ontrac3 steering was an easy install and after a few setting adjustments seems to work pretty good. The application control and sectional control appears to work well but the rate needs to be tweaked a little to get it set properly. Any trouble that I've had a call to Agleader support and it gets sorted out quickly. They have good staff. We will see if my opinion changes as the spraying season continues. Don't get me wrong that everything went perfectly smooth but I've heard of worse issues with other systems.
AgLeader Integra in my Sprayer
0

16,000 acre 1790 16/32 JD, Erratic spacing on main frame.

, ,
Rebuilt planter this past winter, started planting corn and noticed erratic spacing on the 6 main frame rows, wings were planting perfect, I move seed tubes and meters to different rows and problem stayed with mainframe. Rechecked all drive chains and drillshaft bearings, Long frustrating story short, finally replaced the "prodrive" cables and problem solved. Hope my loss of hair will help someone else. Dave
16,000 acre 1790 16/32 JD, Erratic spacing on main frame.
0

JD proshaft row clutches "fix"?

I seem to be replacing about 1-2 row clutches every year and at 530 a piece Im starting to get pissed. Deere wont stand behind them. Has anyone taken one apart and tried to fix them. Any input would be great. Thanks. Also this is coming off a 09 1770nt 24 row
JD proshaft row clutches "fix"?
0

Bent fame 9250

Last fall I had the joy of tweeking the frame on my brand new 9250, does anyone know anyone who is good at fixing them. the only piece that is bent is the main tube on the bottom of header. It wont allow the shaft to drive the gear boxes straight.
Bent fame 9250
0

2020 Header Adaptor Kit

2020 Header Adaptor Kit for 2100 and 2300 series combines.
This is a complete kit with adaptor.
Located in Florence, AL $1500.00
Call 256-710-2270 for more information


2020 Header Adaptor Kit
0

Farm scale ethanol plant

So this might sounds abit of the planet but I'm looking a putting in a farm scale ethanol plant.
The only difference is we want an ethanol plant for the byproduct to use in our dairy not the ethanol.
The ethanol we can use on farm but the wet distillers grain will be our primary product.
My questions am I mad?
Any Aussies know where to start looking for permission or approval for a plant?
I'm guessing US farmers may already have plants of this size what do they cost and where can I find one.

I have found Allard Research & Development | Home that seem to build a small plant.

Thanks for your help.
Farm scale ethanol plant
0

Macdon FD75 75 Hyd Motors Failing

Hi

Just trying to find out whether other users are experiencing continual failures with hydraulic motors on their headers.

We have just had an outside one fail, basically stopped driving, and our centre one is stalling under heavy conditions.

Another one local to us has had three fail in total, two over the space of three days.

Is it possible to fit larger motors, as just wondering whether they don't have enough torque under heavy conditions.

it is a 2013 FD75, one 30ft one 35ft

Thanks
Macdon FD75 75 Hyd Motors Failing
0

Flexi Disc drill, any experience

,
I know a guy that tried to trade one in and they wouldn't take it, said he would make me a good deal, it has been changed to 10" spacing, I cant remember but I think it was in the 35-40 ft range. I know these things pull like a lead sled but seem to raise a good crop. I like that they move a fair bit of dirt. I know they are high maintenance but how bad are they, I have heard of people removing parts to save hair pulling out but I don't know enough.


I have been raising some pretty good corn lately and I am running into residue problems in places and I figure I can buy this for far less than a vertical till machine so I would only be using it in problematic areas.


Also before I make the mistake of buying it has anyone used them in corn and if so what kind of yields and populations and how did it work. I would like to do more corn on corn in the near future as a way to build soil but my seed master wont have nothing to do with it


thanks in advance
Flexi Disc drill, any experience

dimanche 19 avril 2015

0

196 westeel bin wall buckling

I noticed one of my bins has 2 spots where the wall has collapsed 2-3 inches( basically 1 rib). Can I get this collapsed spot pulled back out and add more stiffeners or do I have to live with this and just add more stiffeners to prevent any more damage?

196 westeel bin wall buckling
0

Looking for antique tractors, MF, Oliver, MM, John Deere

, , , ,
Looking for a few pretty rare antique tractors:

Massey Harris 203

Oliver 99 with Jimmy

MF 98 with Jimmy

John Deere with jimmy

MM UDLX (long shot)



Thanks

Looking for antique tractors, MF, Oliver, MM, John Deere
0

JD 750 grain drill

Hey there, bought a JD 750 no till grain drill a few years ago and was wondering if anyone knew of good spot to find a monitor for it. It came with all the sensors and wiring for the drill so I am only looking for the monitor and wiring for the tractor side. The book says you can use a computer trak 150, or 250. The grass box is awful small and gets frustrating getting on and of to make sure you haven't run out

Thanks in advance for your response.

JD 750 grain drill
0

Spartan and Sunflowers

Anybody out there deal with regular sunflowers (non express or Clearfield) and use Spartan as a pre emergent? I've read that you can spray down up to 3 weeks before planting or up to 3 days after but needs a rain to incorporate if done after? How does it do in terms of keeping weeds away until flowers canopy over?

Spartan and Sunflowers
0

Bourgault MRB shims

I was wondering how many shims guys have left on their depth adjustment. I have a new high float with MRB and I am already down to one 1/4" shim and the plastic collar - seems to be leaving me no room for adjusting or coulter wear. I am probably 3/4" - 1" below seeding depth. Any ideas?

Bourgault MRB shims
0

Videology a bar and screening room

0

Sunflower Strip-Till

AGCO does not seem to be promoting their strip-till machine anymore. When it was introduced 4 years ago there were a few videos and some presence at farm shows. Now nothing. Meanwhile, Orthman is continually coming up with new, innovative, additions to their strip-till machine. I think the Sunflower is built better than the Orthman and have thought seriously about buying one but I don't need another orphan underfoot.

Sunflower Strip-Till
0

8960 Cab noise

Does anyone else out there with a John Deere 8960 24 speed, or other similar models notice a hydraulic chatter or hammer?




You can hear it at idle through the floor, it gets worse when you need to use the hydraulics but completely vanishes at full hydraulic flow.

Example: Air cart fan makes it hammer and chatter away steady all day but lifting the toolbar at the headland with fan on will silence the noise. When that noise goes away its really nice and quiet...till I'm done lifting then back to the chatter. I can make the noise get louder just sitting in the seat or steering.




The noise is driving me nuts, I just purchased it recently and I like the tractor otherwise. Are these tractors known for hydraulic noise? Putting that pump right under the cab doesn't help.

8960 Cab noise
0

International 900 help needed

How can I go about testing my sensors individually? Put my meter probes in the plug and check for resistance or do I need seed going through it for it to signal? Reason I ask was had some issues last year and monitor didn't show/alarm for the skips. Does anyone have a pin diagram for the plugs?

Also what should I look for and do as maintanence to get ready for the year besides grease and lubricate like manual recommends?

Thanks.




Attached Images





File Type: jpg image.jpg (712.4 KB)



International 900 help needed
0

Remote Chute opener

Looking for a good remote chute opener with air hoist controls. Anybody have one they like? Lakeshore manufacturings e-mail seems out of service. Thats one I saw at the brandon show.

Remote Chute opener
0

JD 1910 Air Cart

I am putting peas this year with a 1910 John Deer air cart and a 1830 hoe drill.



I am going to be using granular inoculant in the small middle tank and putting it with the seed row.



My question is do I change the agitator from low to high? In the book it says to keep it on low for most crops except barley and grass seed ect. But I am guessing for the innoculant it should be placed on high. Would it hurt to leave the agitators on high for fertilizer, wheat, canola ect? There would be less chance of bridging in the tank.



I also don't have a good seals on the bottom plates blow the meters where you take these plates off and hang the bags on. It appears it is just plastic to plastic seal. Seem hard to do much to seal it.



Vince

JD 1910 Air Cart
0

FS Valmar 7600

Selling a brand new Valmar 7600 never used. I ordered it June 2014 when the weather was wet. Spring is pretty dry here so I don't need it.



60ft booms, mechanical drive, hyd fan (no PTO required), second metering system, 750 floater tires, roll tarp.



$72,000 Cdn



Unit located in SW Manitoba, may be willing to arrange delivery within Manitoba



PM me for contact information

FS Valmar 7600
0

Field IQ/EzBoom

Just installed it on a PT sprayer. How do you turn on booms for a stationary nozzle check?

Field IQ/EzBoom
0

Local chem/hardware shop burnt down

over one hundred 1200L shuttles of mainly glyphosate, trifluralin and gramoxone all caught alight, toxic smoke drifted across town. 2 shops affected.



Fire in Northampton - Video and Images - Everything Geraldton

Local chem/hardware shop burnt down
0

Blow out

Had a blow out & having trouble finding a newie here in OZ.

Tyre companys don't seem to have them here yet, does anyone here in Oz know where i can pick a new one up??

tire size 500 / 85 R24 SVT IMP.

Blow out

samedi 18 avril 2015

0

JD Sectional Control

Just wondering if anybody has had a chance to use their new 1910 cart with sectional control. It would be nice to know what everybody is using for turn off/on times and width of airseeder along with the type of product being applied. We are a good week out yet from trying ours.:trac1:

JD Sectional Control
0

Plugged Liquid N bins

We run liquid N (28-0-0) and have four bins to store the stuff over the winter. A bit always salts out and we circulate it for a few days prior to seeding to get everything mixed back in.



Problem is that this year two of the four bins are completely plugged. Like blocked solid. We can open the valves full and only a tiny trickle of liquid comes out. Pumping water into it doesn't seem to make much of a dent.



Anyone else run into this before? Any ideas what might have happened? The winter wasn't more unusual than any other...

Plugged Liquid N bins
0

Case STX won't move

I did a transmission calibration on a case stx. Oil was warm at operating temperature and the calibration seemed to complete normally. Upon completion the orange exclamation light appeared and the screen shows Transmission Setup. Now tractor will not move forward/reverse!!!! Code shows 56067 and 56002. Both are calibration codes. Changed potentiometer on clutch pedal...still not help. Tractor has sat overnight and now cold so can't get transmission temperature up to 60 degrees to try calibrating again. Does anyone know if doing a calibration at lower temperatures will cause the 56067 code??? Anyone ever have the transmission setup message displayed and what caused it? Any advice would be greatly appreciated, thank you.

Case STX won't move
0

Case STX won't move

I did a transmission calibration on a case stx. Oil was warm at operating temperature and the calibration seemed to complete normally. Upon completion the orange exclamation light appeared and the screen shows Transmission Setup. Now tractor will not move forward/reverse!!!! Code shows 56067 and 56002. Both are calibration codes. Changed potentiometer on clutch pedal...still not help. Tractor has sat overnight and now cold so can't get transmission temperature up to 60 degrees to try calibrating again. Does anyone know if doing a calibration at lower temperatures will cause the 56067 code??? Anyone ever have the transmission setup message displayed and what caused it? Any advice would be greatly appreciated, thank you.

Case STX won't move
0

John Deere 9300 shifting issues

Friend having trouble getting his 9300 JD 24 speed power sc into gear! Seems the clutch isn't disengaging. Any ideas?

John Deere 9300 shifting issues
0

Installing new Elephant Ears on 1640

The lateral edge of the rotor blades (elephant ears) on my 1640 Case combine appear worn and have become quite sharp. there are 2300 hours on the machine. Would this be considered normal wear? Should the edges be sharp? If the blades need to be replaced, do I have to take out the rotor to do so? Any advice/suggestions would be appreciated.

Installing new Elephant Ears on 1640
0

T9.450 with intellaview gps problem

i have for the last two years been switching my nav controller and 262 antenna back and forth from my tractor to combine as needed. Last fall I took the nav and antenna out of the combine and put it on the shelf for the winter. I put the two pieces in my tractor yesterday and it's like my iNtellaview doesn't even know gps was invented let alone installed. When I go to the toolbox there isn't even the menu for nav or gps. When I am at the main run screen the icon that show up in the upper left corner in the squares are blank. Nothing to show signal or anything. All my run screens that I had set up are different like they were returned to a default setting. My memory stick is still in the back of the monitor so I'm at a loss. It's the weekend and even thought it can wait till Monday to call someone it's bothering the **** out of me



Any suggestions?

T9.450 with intellaview gps problem
0

Anyone use a CTS in faba beans, peas, lupins

, ,
Has anyone used a CTS in faba beans, peas or lupins etc...even soya beans? I'm worried about grain loss over the rotors....



Ant..

Anyone use a CTS in faba beans, peas, lupins
0

AFSC crop insurance

Hey guys - haven't dealt with this issue myself in the past, was hoping you guys might be able to let me know what to expect.





Its looking like I will be renting some land this year that had last years wheat crop left out, wasn't swathed. The previous renter apparently hasn't heard from crop insurance whether or not they require him to combine it - he's hoping they don't make him combine. It had some elk get into it over the course of the winter.





Just wondering how much wildlife damage they typically need to see to write it off? How about yield loss before they don't require combining? When do they typically have an answer for the farmer? I've heard rumours that they are making guys combine pretty much anything this year, not sure if there is any truth to that or not. Pretty hard to guess what the yield would be if the crop were to be combined - wouldn't be surprised to see 10 bu / acre out there still, depending on how easily it picks up.





I'm trying to figure out what my plan will be for the land for the spring, but its entirely dependant on what happens with the last guys crop, and there doesn't seem to be a whole lot of answers coming my way as of yet.

AFSC crop insurance
0

Soybean rookie

I live in dryland country and have lost half of my wheat crop due to winterkill, we are considering two options for planting something in those fields.



We are looking at liberty link soybeans or grain sorghum. I personally hate sorghum and have zero experience with soybeans. The liberty link would be a good thing to throw out there to get away from glyphosates for a little bit.



My question is what row spacing and population is ideal for soybeans in my conditions with 14-20" annual moisture? I have a sunflower dribble drill set on 10" spacings and a 16 row White planter on 30" rows.



I would put them to peas but insurance wont allow it, well you can do it but Ill only get 30% coverage on my wheat if I put it to peas. If I put something like sorghum or soybeans out there I can collect 100% on the wheat and insure the beans/milo.

Soybean rookie
0

weird fungus or eggs, ive got no idea

,
random patches of this in areas of a paddock that was wheat last year.



I've asked my a local agro, tried google, but cant find anything to see what it is. Ive never seen it before, dad hasn't either. Thought it was some kind of fungus, but looks more like eggs, honestly dont know at all haha. Its been a very wet last 2 months, and warmer than normal.



We've seen similar before, but not like this.



hoping some one can help, very curious to what it actually is.

weird fungus or eggs, ive got no idea
0

John Deere DTC

If you need full list of John Deere Fault Codes you'll find here:John Deere Fault Codes - Truck Manuals & Wiring Diagrams

John Deere DTC

vendredi 17 avril 2015

0

CaseIH rotor coupling

How does on replace the rotor coupling on a 1660?

CaseIH rotor coupling
0

John Deere 1870 Questions

We are just getting our new 1870 built and set upto go. I have a few questiond.



1) We are NOT using the fertilizer opener because just single shooting in seed trench. Do I still need to use the fert knives to open the ground ahead of paired row openers? Or can i remove the fertilizer knifes?



2) what setting for seed tube depth? Ours came from factory at #7



We will be seeding into damp heavy clay. Any suggestions appreciated.

John Deere 1870 Questions
0

premature wearing of dutch openers

My experience with dutch is not very good . Their warranty is poor and openers wear out way too premature. Anybody else have openers that wear out on the sides behind the carbide. Did approx. 2500 acres with a 35 foot tillage and started having problems at 3500 acres set of points are done . Neighbors using Atom jets and bourgaults you can hardly see the wear with many more acres.

premature wearing of dutch openers
0

calibration morris 7240 cart

If I calibrate the seed rate it is always about 30% out (low) from what the chart tells me.

The chart is dead on, so I still go by that.

Even the dealer could not figure it out.

We are sure we have the right sprockets and stuff for the with and the row spacing.

We even drove instead of turning the crank.

More people ran into this?

I bought the cart new 2 years ago.

calibration morris 7240 cart
0

New Holland Fault Codes

Full list of New Holland Fault Codes see here

New Holland Fault Codes
0

Case IH Fault Codes

Comlete list of CASE Fault Codes see here

Case IH Fault Codes
0

JD 6000 series tractor

I see they are made in Europe. Is this a solid tractor to buy used? Parts availability still good?

JD 6000 series tractor
0

1999 Gleaner R72 Smartrac Lateral Tilt

I just got a new to us 1999 Gleaner R-72 that seems to have everything set up for the lateral tilt system except for the lateral tilt housing itself. So I have a couple of questions.





1. Anybody know where to find a Lateral tilt frame? And also, if you buy it new does it come with all the latches and parts on it or will I have to piece it together?





2. It will be hooking up to a 7000 series header for wheat harvest in Oklahoma. Will feeding not be as good with the added tilt frame or will it still feed good?





Thanks for your help.

1999 Gleaner R72 Smartrac Lateral Tilt

jeudi 16 avril 2015

0

Single acting and double acting hydraulics..?

So I am building a little farm project, i have access to a few old hydraulic rams, but they are all double acting, can I make a double acting cylinder single acting by just blocking off one port? Or does it air lock or anything?



Next question, i always see the single acting cylinder is smaller when paired up with a double acting, for example a header reel. The double acting cylinder is fatter then the single acting cylinder, is there a reason for this? Or is this just inherent to the cylinder design?



Thanks.

Single acting and double acting hydraulics..?
0

Topcon users

So we're trying out a Topcon system 350 with the X30 and RTK on one of our swathers this season, if it goes well we will be getting the rest of the machines outfitted. We have the HiPer Ag base station that I want to keep at the shop. My only concern is how far out will the base station reach? Will I need another base station? I am looking at a repeater for the times that we are in spots that are down in a hole, will the repeater increase the distance of the RTK signal? I want to get everything setup right before we do have a problem once we start cutting. Thanks.

Topcon users
0

jd 1895 opener repair

Anyone have experience changing coulter bearings/hub on the 1895 JD drills? The spindle and gauge wheal arm are seized but I can't get them pressed out. I heated the casting up good but all I could do was free the hub up so it would turn. Does the spindle thread into the gauge wheel shaft? Is that why it won't move? Parts diagram shows a snap ring but I think that just keeps bearing in the hub. Thanks

jd 1895 opener repair
0

Hydraulics question - experts?

I have a Versatile 555 (open center hydraulics) that I am going to be using on a small older Morris 6130 air seeder.





I have done this successfully with my open center Steiger using a different flow control than I am using this time.



The Versatile tractor puts out 2300 psi at 23 GPM which is more than enough for the air seeder.





The airseeder requires 13 GPM at max speed at 2000 psi





I bought an adjustable flow control for the tractor to be able to dial in the fan speed on the air seeder cart.





The flow control is capable of 30 GPM - more than enough for what I'm doing. http://ift.tt/1b2BB6t





My question is this:





The tractor's relief valve is set to 2300 psi (or a touch higher), the air seeder cart requires 2000 psi, and the flow control's relief is factory set at 1500 psi.





What do I need to set the relief valve on the flow control to? Or should I take it back and get one without a relief valve since it will be protected by the tractor's relief?





I want to generate as little excess heat as possible.

Hydraulics question - experts?
0

john deere 6920 duals

Does anyone know if it's possible to put rear duals on a john deere 6920? the operators manual mentions duals but the dealer says it's not possible

john deere 6920 duals
0

Photographer Richard Mosse has

0

John deere 7000 population question

I just bought a 7000 john deere planter 6/13. But it's two separate planters on a double frame. It's 6 rows on the front planter and 7 rows on the back. I can set the population on each planter because they both have their own transmission. My question is say I wanted 160,000 population for beans (I have kinze brush meters) would I set the front planter on 80,000 and then the back planter on 80,000 or would I set them both at 160,000? It seems like the seed spacing would be pretty far apart on 80,000 but I could be wrong. My last planter was a 4/7 7000 series but only had one transmission with chains from the front to drive the back row units. Please let me know what you think.



Thanks,



Russell.

John deere 7000 population question
0

Kubota Tractors

Kubota Corporation of Japan was established in 1890 and has become an international brand leader with a focus on contributing to society by offering environmentally compatible equipment designed to improve quality of life. Kubota Corporation has subsidiaries and affiliates that manufacture and/or market products that are sold in more than 130 countries.



Kubota was the first agricultural machinery manufacturing company in Japan to receive the prestigious "Deming Award," for manufacturing excellence. In 1992, Kubota Corporation received the "Sankei Newspaper Award" as part of the first Global Environment Awards, recognizing the Company’s continuing contribution to protection of environment.



The Kubota tractor has its roots on the Japanese farm. Although Japanese farms are traditionally smaller than those in America, the need for high performance and powerful maneuverability is the same. Kubota Corporation introduced its first tractor to the United States in 1969. Filling a product void in the American marketplace, the Kubota 21 horsepower L200 was an overnight success. As a result, Kubota Tractor Corporation (KTC) was formed in 1972 and the company introduced its first 12 h.p. four-wheel drive tractor in 1974. Although four-wheel drive was common among larger American tractors, it was unheard of in the compact sector and became a benchmark for the industry.

Kubota Tractors from Japan





Over the past four decades, KTC has continued to expand its product line, with four lines of tractors, the BX, B, L and M Series. Kubota has successfully introduced compact construction equipment, compact track loaders, turf equipment, lawn and garden equipment, utility vehicles and a variety of Performance-Matched implements and attachments. KTC is now a leading marketer and distributor of under 120-h.p. tractors in the United States, offering more than 80 tractor models.



Kubota equipment is sold and serviced in the United States through a nationwide network of more than 1,100 authorized Kubota dealers supported by the company’s corporate headquarters in Torrance, California and four division offices and warehouses located in Lodi, California; Fort Worth, Texas; Groveport, Ohio; and Suwanee, Georgia.



Here is you'll find a lot of repairing information

Kubota Tractors
0

Mccormick Ztx 260 hydraulics

How do you get the hydraulics to give constant flow so you don't have to keep holding lever? They are electric hydraulics I believe and as soon as I push lever into hold position the reel on rock picker stops?

Mccormick Ztx 260 hydraulics

mercredi 15 avril 2015

0

Deere row trac quad

Found this on ag talk looks like ole mother Deere is gonna put ih out now got this quad and big quad




Attached Images





File Type: jpg image_1429158688267.jpg (125.8 KB)



Deere row trac quad
0

Protected seed agreement

I ordered some Monsanto seed corn the other day . Seed supplier had me get on line and sighn the agreement that you can't keep any seed or sell as seed. Or they will take your farm and first born... It was a third party company that did the paper work ... He did it also for Bayer westbred. Washington state Another one or two breeders What got me was when they asked me to verify who I was they asked me some ? To verify that it was indeed me filling out the ? One ? Was asked who a former employer was ... They had the last employer I worked for 15 yrs ago that is no longer in existence and they also asked about a old pickup I use to own and what color it was .... How in the heck did they have this and other info? And it wasn't like it took them a fe days to fig out these ? It was a few seconds. I have never shared any of that info with them or any other seed company...

Protected seed agreement
0

STORM Seed treater---who has one?

Who has a storm seed treater? Do you like it? Have you used chemicals besides bayers? If so, how has that worked? Happy with coverage?



I have not seen one working in person, but to me it's still just spraying the chemical in the bottom of auger and mixing it in auger. That's what we have done for years and are never really happy with coverage. Maybe there is something with the Storm that makes it cover better?



Thanks in advance.

STORM Seed treater---who has one?
0

650/65R38 vs 620/70R38 on Case 4430

Looking at a Case 4430 sprayers, and there are two options for the floater tires. Standard is the 650/65R38 and the "optional" is the 620/70R38. Did some quick math, and obviously the 650 is wider, but the 620 will be about 3cm taller. Hard to say which would handle the mud better, but..... I would just guess the 650 as it is wider. Any one have any other opinions? It seems interesting that they option two tires that are so close in size.

650/65R38 vs 620/70R38 on Case 4430
0

Bourgault 7700 fan speed

I have a bourgault 3320/7700 cart and am having issues getting enough fan speed. Im seeding peas so not running banders or 2nd fan. It is a high speed fan but only able to get right at 5000rpm out of it. Have a john deere 9560r pulling it and I have openers and fan on separate pumps. Also tried switching them and same result. Anyone have an idea?

Bourgault 7700 fan speed
0

Willies responce to rumour

There is an internet rumor that Willie Nelson died .The response






Willies responce to rumour
0

Hydraulic Fittings

In this politically correct world you cannot use the terms male and female. Now you need a #8 pusher or catcher fitting

Hydraulic Fittings
0

jd 4450 transmission leaking again

I need some info about the bushing supports for the lower sensing shaft on a John Deere 4450 tractor. These bushing supports were replaced several years ago by the John Deere dealer, but now transmission oil again is leaking like a sieve. Is this a common problem with these tractors? We rarely use the three point hitch. Is this a repair I could handle, or must it return to the dealer? Thank you for your help!

jd 4450 transmission leaking again
Inscription à : Articles (Atom)

Popular Posts

Categories

Unordered List

Text Widget

Blog Archive

Followers

Fourni par Blogger.