I'm a older man that runs a 8010 for a very good friend of mine.
Problem-- yesterday while waiting for the truck, I shut the machine off to do a good check over. 20 min. later tried to start up and nothing, turned key, nothing then a few clicks then nothing. Now a day and half later still same thing, haven't solved it.
I'll tell you what I've done and then hope someone can tell me what I've missed.
Being older, yes I've cleaned every connection related to the starter assym.
New batts, at start of season.
Replaced the 12-24 volt relay by the batteries ,$$$$$$ had one go bad 5 years back on a new 9130, batteries wouldn't stay up, this relay regulates charging and starting on 24 volts then run on 12. Thought sure this was our problem- not-- costly guess!!!
Selinoid by starter checked and is good.
Jumper started with 24 volt power pack, connected direct to starter, starter turned engine over fine but would not start. I imagine in start mode key and computer activates other things, timing, fuel, etc. so just turning engine over is not the answer.
Took out batteries last night and charged each
checked all fuses
tried jumping with truck per instructions -no good
One thing I did notice while running a computer check on volts, was
CCM 1 2&3
battery voltage should have 18,8, I have 10.7 on all three
Key switch
voltage should be 18.8, I have 10.7 on all three
Don't know exactly what this means, but only thing out of place on all the checks I ran. Why 18.8 and not 24 or 12 something that would make sense, you got me'
Talked to to dealers with no help. These are dealers I know personally for a long time and friends in mechanics dept. they just didn't no.
On the 9130 battery problem, it was solved by one of you members on the forum. Dealer was blank on that one also back then. New machine, fought it threw most of corn harvest in Iowa!!!! SAD!!!
That's all I got, sure would and will appreciate any help. Thanks, Gary PS, I can usually master about anything but this ones got me stumped!!!!
8010 CIH combine won"t start- need new ideas!
Problem-- yesterday while waiting for the truck, I shut the machine off to do a good check over. 20 min. later tried to start up and nothing, turned key, nothing then a few clicks then nothing. Now a day and half later still same thing, haven't solved it.
I'll tell you what I've done and then hope someone can tell me what I've missed.
Being older, yes I've cleaned every connection related to the starter assym.
New batts, at start of season.
Replaced the 12-24 volt relay by the batteries ,$$$$$$ had one go bad 5 years back on a new 9130, batteries wouldn't stay up, this relay regulates charging and starting on 24 volts then run on 12. Thought sure this was our problem- not-- costly guess!!!
Selinoid by starter checked and is good.
Jumper started with 24 volt power pack, connected direct to starter, starter turned engine over fine but would not start. I imagine in start mode key and computer activates other things, timing, fuel, etc. so just turning engine over is not the answer.
Took out batteries last night and charged each
checked all fuses
tried jumping with truck per instructions -no good
One thing I did notice while running a computer check on volts, was
CCM 1 2&3
battery voltage should have 18,8, I have 10.7 on all three
Key switch
voltage should be 18.8, I have 10.7 on all three
Don't know exactly what this means, but only thing out of place on all the checks I ran. Why 18.8 and not 24 or 12 something that would make sense, you got me'
Talked to to dealers with no help. These are dealers I know personally for a long time and friends in mechanics dept. they just didn't no.
On the 9130 battery problem, it was solved by one of you members on the forum. Dealer was blank on that one also back then. New machine, fought it threw most of corn harvest in Iowa!!!! SAD!!!
That's all I got, sure would and will appreciate any help. Thanks, Gary PS, I can usually master about anything but this ones got me stumped!!!!
0 commentaires:
Enregistrer un commentaire